Product Reviews · Surface Drilling Equipment · 16 min read

Atlas Copco ROC D3-01 Drilling Rig Review: Specifications, Applications and Buyer Guide

The advertised Atlas Copco ROC D3-01 is a used 2009 tracked surface drilling rig offered at US$73,000. The seller reports 6,149 engine hours, 1,810 drifter hours, a 156 hp Cummins QSB4.5 Tier 3 engine and an operating weight of 23,150 lb. Its value for a particular project depends on the installed rock drill, records, operating condition, tooling and delivered scope.

Listing details at a glance

What is the Atlas Copco ROC D3-01?

Atlas Copco describes the ROC D3 as a compact, medium-size bench-drilling rig designed for mobility on rough ground. The manufacturer literature identifies applications on small and medium construction sites, in built-up areas and in the dimension-stone industry.

It is a surface drilling rig—not an underground jumbo and not a full-face tunnel-boring machine. That distinction matters when comparing fleet requirements, drilling methods, operator competencies and project services.

Hole range, feed and rod handling

The manufacturer brochure publishes a model-family hole range of approximately 41–89 mm. For the D3-01, it lists a 4,240 mm feed travel and maximum feed force of 20 kN. The standard-equipment list references a double drill-steel support and rod-handling system.

Those figures describe the model rather than a guaranteed result from this used machine. Ask for the exact feed, rod sizes, bit range, rod-handling arrangement and included tooling. Inspect alignment, wear surfaces, hose guides, cylinders, supports and interlocks, then witness a controlled drilling demonstration.

Cummins power, compressor and hydraulic rock drill

The seller lists a Cummins QSB4.5 diesel rated at 156 hp at 2,000 rpm and Tier 3. Atlas Copco literature publishes 116 kW / 156 hp for the model. During inspection, check a true cold start, fluid levels, leakage, exhaust condition, cooling performance, fault codes, charging system and service records.

The brochure lists an Atlas Copco screw compressor at 8.5 bar and up to 95 l/s for the D3-01. Verify air delivery under load, oil condition, hoses, separators and leakage. Reduced flushing or contaminated air can affect drilling performance and component life.

Atlas Copco literature references COP 1240 and COP 1640 hydraulic rock-drill options. The seller reports 1,810 drifter hours but does not identify the installed model. Confirm the drifter plate, serial number, rebuild history, impact and rotation behavior, lubrication and available parts support.

Dust collection and exposure control

The manufacturer’s standard-equipment list includes a DCT 140 dust collector. Confirm what is fitted to this rig and inspect filter elements, seals, suction hose, hood, valves and cleaning function. A live test should show whether dust is captured at the collar rather than released around the operator or work area.

Effective dust control supports visibility, equipment care and exposure management, but it does not replace a site-specific assessment. Apply competent controls for respirable crystalline silica, noise, exclusion zones and local regulatory requirements.

Mobility, dimensions and transport planning

Atlas Copco literature gives approximate dimensions of 10,000 mm long, 2,390 mm wide and 3,600 mm high for the D3-01, plus 340 mm ground clearance, ±15-degree track oscillation and a maximum tramming speed of about 3.3 km/h. Published climbing ability is 20 degrees without a winch and 30 degrees with a winch.

These are model-level figures, not a transport declaration for the listed unit. Confirm the serial-specific mass, fitted options, boom position, loading method, tie-down points, carrier condition and legal transport envelope. Plan permits, route restrictions, trailer capacity, cleaning and offloading before dispatch.

Applications that may suit the ROC D3-01

• Surface bench drilling on small and medium construction projects.
• Quarry-support and production-development work within the confirmed hole plan.
• Dimension-stone drilling.
• Built-up sites where the rig’s compact footprint and reach suit the controlled work area.
• Rough-ground drilling where access remains within the manufacturer’s operating limits.

Match the machine to geology, required hole diameter and depth, production rate, blast design, tooling, compressor needs, dust-control standard, maintenance support and local law.

HSSE and operational considerations

Use trained, authorized operators and the correct manual. Planning should address ground stability, drilling and blasting interfaces, exclusion zones, line-of-fire exposure, drill steel, rotating equipment, high-pressure air, hydraulic stored energy, noise, dust, fire prevention, overhead and underground services, traffic, lighting and emergency response.

Isolate and verify zero energy before maintenance. Inspect guards, emergency stops, hoses, alarms, access, work lights and fire protection. This review does not replace a competent inspection, manufacturer instructions, risk assessment or legal compliance review.

Used-machine inspection checklist

• Confirm serial plates, ownership documents, seller authority and any liens.
• Reconcile engine and drifter hours with electronic records and service invoices.
• Witness a cold start, tramming test and controlled drilling demonstration.
• Inspect the engine, cooling, compressor and hydraulic system for leakage and performance.
• Check the feed beam, supports, rod handling, cylinders, pins, bushes and hose routing.
• Identify the fitted rock drill and review rebuild history, pressures and lubrication.
• Test the dust collector, filters, hood, suction hose and cleaning cycle.
• Inspect track chains, rollers, sprockets, final drives and oscillation.
• Test controls, instruments, lights, alarms, guards and emergency stops.
• Inventory rods, bits, tooling, manuals, spare parts and optional equipment.
• Verify transport dimensions, configuration-specific mass and loading arrangements.
• Commission an independent drilling-equipment inspection before payment.

Product location requires confirmation

Request current dated photographs, the serial number, a cold-start video, a drilling demonstration and the nearest practical transport or export hub before appointing an inspector or carrier.

Worldwide shipping and customs support

Omnia Machinery advertises worldwide shipping, regular updates and customs paperwork included. These are seller-stated services, not a guarantee of delivery to every destination. Ask for a written delivered quotation covering collection, loading, dismantling, inland haulage, freight, insurance, customs documents, duties, permits, offloading, reassembly and commissioning. Confirm the Incoterm and when cost and risk transfer.

Current seller offer — Verified 4 November 2026

Video availability

No official, closely matched Atlas Copco or Epiroc ROC D3-01 video was verified for this review. Rather than embed a dealer reupload or a different machine as if it represented the listed unit, buyers should request a fresh walkaround, cold-start and drilling-demonstration video tied to reference US2240.

Questions to ask before contacting or paying the seller

• Is reference US2240 still available at the displayed price?
• What is the rig’s exact physical inspection and collection location?
• What is the complete serial number and ownership history?
• Are the 6,149 engine hours and 1,810 drifter hours documented?
• Which hydraulic rock drill is installed, and when was it last rebuilt?
• Which rods, bits, couplings and tools are included?
• Can the seller provide a cold-start and live-drilling demonstration?
• Are there active warning codes, leaks or outstanding repairs?
• When were the engine, compressor, drifter and hydraulic system last serviced?
• Has the feed beam, rod handler or undercarriage been repaired?
• Does the dust collector operate correctly under drilling load?
• Are manuals, service records and parts information available?
• Can an independent specialist inspect and test the rig?
• Does the price exclude taxes, loading, transport or optional tooling?
• Can the seller arrange delivery to the intended destination?
• Which customs documents and export services are included?
• Are any warranties or return terms offered in writing?
• What deposit, payment protection and release documents apply?

Frequently asked questions

What is the Atlas Copco ROC D3-01 used for?

Atlas Copco literature describes the ROC D3 as a compact medium-size surface bench drill for small and medium construction sites, built-up areas, rough terrain and dimension-stone work. Project suitability depends on geology, hole plan, tooling and the exact machine configuration.

Is the ROC D3-01 an underground drill?

No. It is a tracked surface or bench drilling rig, not an underground jumbo or full-face tunnel-boring machine.

What hole sizes can the ROC D3 drill?

The manufacturer brochure publishes a model-family range of approximately 41–89 mm. The achievable diameter depends on rod type, bit, rock drill, rock conditions and the installed configuration.

How much does the ROC D3-01 weigh?

Atlas Copco literature gives approximately 10,500 kg or 23,150 lb for a ROC D3-01 with the referenced rod-handling system. Confirm the actual transport mass and fitted options.

Which engine does this advertised rig use?

The seller lists a Cummins QSB4.5 Tier 3 diesel rated at 156 hp at 2,000 rpm. Verify the engine plate, serial number, hours and service records.

Where is this machine located?

The detailed seller page identifies Montana, while the marketplace header and seller address reference Miami, Florida. Ask for the current physical inspection and collection address before arranging travel or transport.

Does the seller offer international shipping?

Omnia Machinery advertises worldwide shipping, regular updates and customs paperwork. Obtain a written destination-specific quotation and confirm every included cost and responsibility.

Which hydraulic rock drill is fitted?

The listing provides drifter hours but does not identify the installed rock-drill model. Atlas Copco literature references COP 1240 and COP 1640 options; confirm the exact fitted unit from its plate and records.

What should be inspected before buying?

Priorities include machine identity, engine and drifter records, cold start, hydraulics, compressor, dust collector, feed beam, rod handling, rock drill, undercarriage, controls and safety devices.

Is the advertised price still available?

The seller displayed US$73,000 when checked on 4 November 2026. Price and availability can change, so confirm the live listing before making arrangements.

Final assessment

The ROC D3-01 combines a compact tracked carrier, a long aluminium feed, rod-handling capability, flushing-air capacity and model-level support for common medium-site hole diameters. The advertised engine and drifter hours, Cummins power and US$73,000 asking price make this unit a reasonable candidate for documented technical due diligence.

The buying decision should rest on the exact physical location, serial identity, installed rock drill, drilling demonstration, service history, dust and air performance, undercarriage condition, included tooling and delivered cost.

Join the discussion

Would you use the ROC D3-01 for construction drilling, quarry work or dimension-stone operations? Share your intended application or inspection questions in the comment section below.

Explore more product reviews · Browse the HSSE article library

HSSE TIPS — Worksite Safety Hub
Every Task. Every Person. Home Safe.